LinxVIEW论坛-斯科道

 找回密码
 立即注册
查看: 2687|回复: 2

LabVIEW Raspberry Pi 软件安装环境指南

[复制链接]

494

主题

694

帖子

2340

积分

版主

Rank: 7Rank: 7Rank: 7

积分
2340
发表于 2019-4-16 19:33:26 | 显示全部楼层 |阅读模式
回复

使用道具 举报

494

主题

694

帖子

2340

积分

版主

Rank: 7Rank: 7Rank: 7

积分
2340
 楼主| 发表于 2019-4-16 20:13:26 | 显示全部楼层
本帖最后由 Scadao 于 2019-4-16 20:15 编辑

  • 原文链接

  • Download a Raspbian image
    • LINX was developed using Raspbian Jessie.

  • Unzip the Raspbian image.


  • Download and Install Win32 Disk Imager.


  • Use Win32 Disk Imager to load the Raspbian image onto an SD card.


  • Insert the SD card into the Raspberry Pi.


  • Connect ethernet to the Raspberry Pi


  • Power on the Raspberry Pi.


  • Note: The next step requires that the RPI has SSH enabled, however as of November 2016 Raspbian has SSH disabled by default. Manually enable SSH by following these instructions.

  • Launch LabVIEW and open the Target Configuration Wizard from Tools»MakerHub»LINX»Target Configuration.


  • Enter the Raspberry Pi's Hostname or IP and a username and password with root privileges and click connect.
    • Default Hostname is 'raspberrypi'.
    • Default Username is 'pi'
    • Default Password is 'raspberry'


  • Click the Install Software tab.


  • Click Install.


  • Review any warnings and complete the installation.


回复 支持 反对

使用道具 举报

494

主题

694

帖子

2340

积分

版主

Rank: 7Rank: 7Rank: 7

积分
2340
 楼主| 发表于 2019-4-16 20:31:28 | 显示全部楼层

原文链接

  • Open example finder by clicking Help»Find Examples.


  • Search for LINX.


  • Open LINX - Blink Advanced.


  • Save a copy of the example to the desktop, name it Blink and close the original.


  • Create a new empty LabVIEW project by clicking File»New»Empty Project.


  • Choose to add the Blink VI to the project when prompted.


  • Add a new LINX target to the project:
    • Right click the top project item and choosing New»Targets and Devices.
    • Expand the LINX folder to discover LINX devices on the network
      or

    • Choose New Target or Device, exapnd the LINX folder and select the appropriate target type. (Make sure to manually set the IP).



  • Right click on the LINX target in the LabVIEW Project and choose Connect.


  • Open the Blink VI.


  • Switch to the Block Diagram.


  • Change the LINX Open from Serial to Local I/O and remove and broken wires.


  • Save and close the Blink VI.


  • Move the Blink VI under the LINX target in the LabVIEW Project.


  • Open the Blink VI.


  • Update the Digital Output Channel to match the DO channel connected to the LED.


  • Run the VI.




回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|Archiver|手机版|小黑屋|SCADAO  

GMT+8, 2021-10-25 08:49 , Processed in 0.990928 second(s), 23 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

快速回复 返回顶部 返回列表